Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Richmond?
Panel replacement in Richmond typically runs $250 – $500 for a single section, including the new panel and labor to fit it. Most jobs land in that range once a technician matches the panel profile and color to your existing door. The written estimate you get before any work starts is what sets the final price.
That figure covers a standard residential section on a door we can still source parts for. A full row of panels or a larger custom door moves toward the top of the range, and doors where the section is no longer made can push past it because the fix becomes a partial or full replacement rather than a swap. If your door is stuck open, dented through, or leaving the house exposed, call (855) 774-2730. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Panel Replacement Cost Breakdown (2026)
Here’s how the numbers break down for a panel job in Richmond, alongside the other repairs that often come up on the same visit. These are typical estimated ranges for the Richmond market. The written estimate sets the final price.
| Job | Typical Estimated Range |
|---|---|
| Panel replacement (single section) | $250 – $500 |
| Spring repair (one spring) | $180 – $340 |
| Cable repair | $130 – $250 |
| Track realignment | $120 – $240 |
| Roller replacement | $110 – $220 |
| Opener repair | $120 – $320 |
| Opener installation | $250 – $550 |
| New door installation | $700 – $2,200 |
| General garage door repair | $150 – $600 |
A spring note worth flagging: spring prices are per spring. Matched pairs almost always get replaced together, so a pair costs about twice the single-spring range. That’s not an upsell. A door running on one new spring and one tired spring will wear unevenly and can leave you right back where you started.
What moves a panel job up or down? The panel profile and material matter most. A flat steel section on a common door is the simplest case. A raised-panel carriage-style section, a wood or composite door, or a discontinued color pushes the price higher because the part is harder to source. Labor adds time when the section needs the tracks loosened or the torsion system relieved to seat it correctly. On the low end, a single dented bottom section on an in-production door with no damage to the tracks or springs is about as clean a job as panel work gets.
What Affects Panel Replacement Pricing in Richmond
- Panel profile and manufacturer. We work on Clopay, Amarr, Wayne Dalton, Raynor, and the other major brands, and matching a panel means matching width, height, rib pattern, and color. A common profile off a widely installed line is quick to identify and source. An older or discontinued profile takes more legwork and sometimes means the section can’t be matched at all. Brand-specific knowledge here saves you from trial-and-error parts swapping.
- Damage extent. One dented or cracked section is a straightforward swap. Damage that spread into the tracks, hinges, or rollers adds line items from the breakdown above. A door hit hard enough to bend the bottom section usually has a bent track to go with it.
- Door type and material. Steel is the most available and the easiest to match. Wood, composite, and full-view aluminum-with-glass doors cost more to repair because the panels are pricier and the fit is fussier. Glass lites in a full-view panel add material cost on top.
- Access and opening size. A standard single-car opening is simpler than a double. An oversized or custom-width door may need a panel cut or a special order, and getting it in place takes two technicians.
- Richmond’s humid summers and freeze-thaw winters. The region swings from sticky summer humidity to winter nights that drop below freezing. That cycle works on the seams and joints of a door over time. Steel sections can show rust along the bottom edge where moisture collects, and wood sections can swell at the joints. When we look at a damaged panel, we check the sections around it for the same wear, because replacing one rusted bottom panel on a door with three more on the way is money spent twice.
- Whether the door is still supported. A door on a current production line can get a matching panel. A door old enough that the manufacturer stopped making the profile may only have a full-door option. That’s the main reason a panel job occasionally turns into a new door installation at $700 – $2,200.
What a Panel Replacement Visit Looks Like
The first thing we do is identify the door. Manufacturer, profile, width, height, color, and whether the panel is still available. On a Clopay or Amarr door this is usually quick because the branding and profile are recognizable. On an unbranded or older door it can take a closer look, which is exactly where brand familiarity earns its keep. We’d rather spend ten minutes confirming the match than order a panel that shows up wrong.
Once we confirm the panel, the actual swap is the easy part. The old section comes out, the new one seats into the existing hinges and tracks, and the door gets cycled to check the balance. If the tracks got knocked out of line when the door was hit, we straighten or replace them. If a hinge or roller was damaged in the same event, we handle it in the same visit. One call covers the panel, the hardware, and the balance check.
If the damage came with a broken spring, we deal with that too. Spring work is the most hazardous repair in this trade, and it’s not a job for a homeowner with a winding bar and a YouTube video. Torsion springs store enough energy to break a wrist or worse. We do that work safely, and we’ll tell you plainly when a spring is on its way out even if it hasn’t failed yet.
Not sure whether you need a section or the whole door? That’s a reasonable question with a real answer, and we cover the repair-versus-replace math in our guide to panel replacement. If your door isn’t moving at all and you need someone now, our Garage Door Repair Richmond Pros team handles emergency calls when a stuck door traps a car or leaves the house open.
How to Save on Panel Replacement
- Get the panel matched, not guessed. A technician who knows your brand avoids the most expensive mistake in this job: ordering the wrong panel and paying for a return and a second order. Matching by profile beats matching by eye from a photo.
- Fix it before the damage spreads. A dented bottom section that’s still sealed is a panel job. Once water gets behind a bent section and the metal starts to rust through, the sections above it start going too, and the cost climbs toward the full-replacement range. Handle it early.
- Combine repairs on one visit. If the tracks are bent or the rollers are worn, get them addressed in the same trip as the panel. One visit covers the repairs and saves you a second appointment for work that has to happen anyway.
- Ask about a repair-versus-replace comparison. If the door is old and the panel is discontinued, a new door at $700 – $2,200 might make more sense than chasing a part that no longer exists. We’ll lay out both numbers so you can decide.
- Get the estimate in writing, free. Every job we quote starts with a free estimate, and the written figure is the price. Call (855) 774-2730. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Panel Replacement vs. a New Door: Which Makes Sense?
Panel replacement is the right call when the rest of the door is sound and the section can be matched. It’s the cheaper option ($250 – $500 versus $700 – $2,200 for a new door), it’s faster, and you keep the door you already have. A dented bottom section on a door with good springs, straight tracks, and a current profile is the textbook panel job.
A new door starts to make sense when the panel can’t be sourced, when several sections are showing the same wear, or when the door’s springs and tracks are also near the end of their life. In that case, putting $400 into one panel on a door that needs another $500 in repairs is money spent on a door you’ll replace soon anyway. We’ll tell you which side of that line your door is on. We don’t push a new door when a panel will do the job.
Why Brand Knowledge Matters for Panel Work
Panel replacement is a matching problem before it’s a labor problem. The right panel has to fit the door’s profile, height, and color, and the fastest way to get there is knowing the manufacturer’s catalog. Our technicians work on Clopay, Amarr, Wayne Dalton, Raynor, LiftMaster, Chamberlain, Genie, and Craftsman products. That means we recognize a door quickly, know which panels are still in production, and source the correct part without guessing.
Our technicians have up to 13 years of experience, and the panel jobs they see most are the ones that come from a car backing into a closed door, a tree limb, or a hard hit from a bike or mower. Those are common in Richmond’s older neighborhoods, where garages sit close to the street and the driveway is tight. The fix is usually a section, but the diagnosis is where the value is.
FAQs – Panel Replacement Cost
How much does panel replacement cost in Richmond?
Panel replacement in Richmond typically costs $250 – $500 for a single section, including the panel and labor. The written estimate sets the final price. Call (855) 774-2730 for a free estimate.
Is it cheaper to repair a panel or replace the door?
Repairing a panel is almost always cheaper: $250 – $500 versus $700 – $2,200 for a new door. Replace the door instead when the panel is discontinued, several sections are worn, or the springs and tracks are also near the end of their life. Call (855) 774-2730 and we’ll compare both numbers for your door.
Can you match my door’s panel color and profile?
Usually yes. We work on Clopay, Amarr, Wayne Dalton, Raynor, and other major brands, and we match by profile, size, and color. If the panel is no longer made, we’ll tell you straight and lay out the alternatives. Call (855) 774-2730 to check your door.
How much does a dented bottom panel cost to fix in Richmond?
A dented bottom panel typically costs $250 – $500 to replace, assuming the section is still in production and the tracks and springs are fine. Damage that spread into the tracks adds $120 – $240 for realignment. Call (855) 774-2730 for an exact quote. Estimates are free.
Can you come today?
Often, yes. We offer same-day service when a door is stuck or a panel is hanging loose, and emergency response when the house is left open or a car is trapped. Call (855) 774-2730. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Get a Free Panel Replacement Estimate
If a section of your door is dented, cracked, or rusting through, don’t wait for the damage to spread. A panel job handled early stays in the $250 – $500 range. Left alone, it can turn into a full replacement. We’ll identify your door, match the panel, and give you a written estimate before any work starts. The written estimate sets the price, and there’s no charge for the estimate itself.
Whether it’s a single dented section or a door that’s stopped moving entirely, one call covers it. Call (855) 774-2730 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Richmond market as of 2026. Garage Door Repair Richmond Pros offers free estimates – call (855) 774-2730.
What Our Customers Say
"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Rafael Ramirez"Both cables had come off the drum and the door was hanging crooked. I'd watched a video and was about ten minutes from trying it myself, which the tech told me would have been a genuinely bad idea. Glad I called."
- Megan Brooks"Opener works, remotes are programmed, no complaints on the work. Took three days to get on the schedule though, so if you've got a car trapped inside, say so when you call."
- Cole Delaney